Search results

So I'm kicking around the idea of going LS, and I'm almost positive I am going to, but I have well under 1000 miles on this trans I had built with about the best of everything for the 700r4 but if I do the swap I will go with an electronic controlled trans so this one would go up for sale. Is...

I'm currently on the fence about going LS-- but it would be NA for now. I just wanted to see if there were any big expenses being left out besides the oil pan, cross member, and motor mounts. I'm not worried about labor or wiring. I'm only looking for costs of hard parts aside from the actual...

The truck has taken a turn for the worse, I'm waiting on my ride to go get a comp tester but I'm pretty sure a rebuild is going to be in order.. I wish it was the turbo seals but I doubt it, 2 qts of oil in 2 days, way richer than it used to run at the same boost levels too, from 11.5 to 10.1...

I don't remember my last trans ever even shifting into 4th, it would ride up close to 5k RPM and not shift. The new one shifts around 4400 and drops to 3000 which feels a bit early but still pulls much harder than before. I've experimented with holding 3rd a bit longer, to 4700-4800 or so and it...

This is out of a Hahnracecraft Super 20g, which is a rebadged MHI TD06H-20g. I purchased from a shop as new and have not used it other than for pictures in another thread. $315 NO TURBINE HOUSING! Stocker will need to be machined or you will need to buy a new one, which can be had for $120...

I'm picking it up today from Atomic as recommended by a few guys on here. I bought a 2800 stall from Edge racing converters, after it was recommended and I saw a lot of good reviews. The owner was helpful and quick to respond to any questions. I bought the rebuilt kit through probuilt...

Just curious if there's a reason to go with one or the other, like better low pw performance for idle, etc Thanks

I searched forever and couldn't find a damn thing so I bought a te06h-24v in need of a rebuild for $100. The other turbo is a new hahn 20g that I was planning on using but decided it was too small. The first two pics are a rough comparison of lengths of the td06h-20g and the te06-24v with the...

Any gt35 frame for that matter, preferably t3 in 3" vband out--curious to see how compressor fits as well as down pipe setup.. I was going to toss in a new td06h 20g I bought but am having second thoughts and would like something with head room. Looked at doing a 25g comp with a te06h but the...

I bought a couple of tuff support 613061 which is supposed to be equivalent to 4451, 95112, all come up as being correct application-- but these are very hard to compress and when installed ended up snapping the hinge off the window. Anyone used these? I feel like these would be stiffer and...

Lucky find on ebay. It's a brand new td06h 20g 10cm² that I found for $430.. I'll be sending it out for a bit of work and hopefully have it put on some time in august

Are there any years or vehicles in particular for a 4l60e that will bolt right in? From what I've found, 93-97 4l60e should match up and have the same 4 bolt for tail shaft.. But what about the awd? Looking to make this swap if it can be thrown in and hooked up to controller.. Who's done it?

So I'm parked here on the side of the road, truck died and coasted to a stop and now it won't start. Cranks fine just will not start. I put a new ignition coil earlier tonight, I put the old one on and that doesn't work now either. Any ideas? I have limited tools, 1/4" drive socket set, no meter

I just got around to upgrading my fuel pump and figured I'd have a little room to play before doing injectors but saw that I am hitting 99.7% DC at 4600 rpm on 18 psi, AFR at 11.9:1. Fuel pressure is at 42. I was just curious what kind of power this equates to at the crank, can one just...

I just finished putting one in last night(pain in the ass, no idea how guys say it's a 30 minute job lol) but is anyone else running this pump? https://www.amazon.com/gp/aw/d/B004KW4SDO/ref=sxl1?ie=UTF8&qid=1467485876&sr=1&pi=AC_SX236_SY340_QL65#immersive-view_1467485863104 I bought it off of...

Planning on having my trans done this July and I'm thinking this is the route I will go, but I was curious what setups, if any, people are running with this converter. My intentions are to run it with a gtx3076 or similar turbo but I won't have that until mid fall at the earliest, so it would...

It will not shift at all unless I left off gas.. I was doing some reading online and in the manual and it seems like the most common cause is worn 3-4 clutch.. That said, is that a costly fix to the point where I might as well build up an entire new trans, seeing as this is at 168,500 now? Any...

Currently I am debating on ditching my magnaflow 2.5" cat and maybe the muffler as well. As of now I can hit 110 and hold 17±.5psi the entire way, but notice that my wgdc drops dramatically, to around 30% by 105ish. There is no boost creep at all, but I suspect that it is definitely getting...

Sorry but I'm curious :rotf: I know a lot of cars with shitty traction and a few others (BMW and ricers) use this as a "measurement" of power, rather than 0-60, so I'm curious what kind of times you guys have on logs from 60-100? On my stock everything Ty with magnaflow cat, I hit exactly...

Looks like a steal if it's a legit?? http://chicago.craigslist.org/wcl/cto/5418712268.html