What did you do to your SY/TY today?

Status
Not open for further replies.
SloGN

SloGN

9Sec Alky V6
I dropped the trans pan and swapped out the filter/fluid and lock solonoid and i also changed the t-case fluid. I then cleaned underneath it and checked the other fluids while i was there. I'm gonna be swapping out the prop shaft tomorrow.


then cleaning on the top side happens to get ready for autofair.
 
CAMSTY

CAMSTY

SyTy Obsessed
Re: What did you do to your SY/TY today?

I drove it to Costco with the wife and kids and loaded it with $425 in grocheries.........can't do that in a Vette :)

Tommorrow, it gets a oil change from it's break in oil to synthetic before a trip to the track:tup:
 
K5Cruz

K5Cruz

New member
Re: What did you do to your SY/TY today?

I drove mine to work this morning, then I washed and waxed it. Finally back on the road after a year and a half.
 
M

MadPSI

Member
Re: What did you do to your SY/TY today?

I drove mine to the fabricator for some A2A IC piping. Sounded funny running the truck N/A with the turbo blowing air into the atmosphere.
 
CarbonFiber AWD

CarbonFiber AWD

Donating Member
Re: What did you do to your SY/TY today?

Swapped out the tranny and rebuilt shift cable and mounted the freshly wetsanded and polished bed ( beds been narrowed too ) and gate.,with stainless hardware..... Installed the new tail lights and bulbs...Just finished up here at 12:45 am.;)
Cheers,Vinny
 
Loeryder

Loeryder

New member
Re: What did you do to your SY/TY today?

made the payment on the storage locker and sent Ken a check for fog light lenses and control arm sleeves.
yeah all it did today was cost me more money... another day in the life of...
 
NJ93TY

NJ93TY

Donating Member
Re: What did you do to your SY/TY today?

I finished replacing the half shafts, and fixed my broken wire to the ABS sensor, set my FP and may actually drive it this weekend. Then after I pulled it out of my storage bin and some rednecks a few doors down who were loading furniture saw it, came over, one looked at the intercooler in front cause I have the front bumper off and yelled back to his buddy "hey look at this turbo" (wow, have I mistaken my intercooler for a turbo?):banghead: :rotf: Then the other one says, "nice body kit" The last one finally comes over, looks on the inside, see's all my gauges, looks at the center console and goes "oh its stick too"? :rotf: I almost died:D
 
JSM

JSM

Active member
Re: What did you do to your SY/TY today?

Last night it made sure 4 jack stands didn't get stolen. Tonight it will hopefully get a sway bar or 2 installed. It does run still though and if it wasn't 2ft in the air would even drive.
 
SYO237

SYO237

SyTy Registry
Re: What did you do to your SY/TY today?

installing a PLX DM-5 and trying to get it to work, color sanding the new C5 wagon wheels, installing Greddy E-01 boost controller
 
D

DRUNK411

Member
Re: What did you do to your SY/TY today?

(yesterday) I Swapped out my metal iIC lines for the heater hose trick, set the timing, and pulled the oil cooler line off the back of the remote setup to get ready for the new one that comes in today that was leaking, I could go on and on if you asked what have I done to it in the past week!
 
Brassmonkey

Brassmonkey

Cruzin' Mel Man
Re: What did you do to your SY/TY today?

I drove mine to the track for test and tune last night.

Rednecks in Jersey? I don't believe it!...haha
 
SY2455

SY2455

70's Veteran
Re: What did you do to your SY/TY today?

I just got up and getting ready to leave for work, therefore I decided to let more dust settle on mine while it sets in the garage today.
 
4C FED

4C FED

Absolutum Dominium
Re: What did you do to your SY/TY today?

Jacked up the front & rear, spun the tires 90 degrees & set her back down (I don't want any flat spots on my 9 month old, zero mile tires).
 
RScal

RScal

Just Getting Started...
Re: What did you do to your SY/TY today?

Drove it to work...Just chillin' in the parking lot until lunch time...
 
dgoodhue

dgoodhue

BuSTeD 4.3
Re: What did you do to your SY/TY today?

I cut down the corner intake stud bolts by 3 threads, because my Vortec heads weren't drilled deep enough. I am waiting for a new Melling Select Oil Pump.
 
Status
Not open for further replies.
Top