Search results

Finally got the little truck over to the alignment shop. Got the coil overs done on the front, bell techs on the back, C5 Z06 brakes, and the black ZR1's completed. I'm pretty happy with the result. And oh yea, the new license plate. LOL

OK, so #0408 has the suspension, brakes, wheels and tires all completed. It's now time to move to exhaust and tuning. Already have the cai done...otherwise bone stock. I'm not looking to make it radical or anything. But I'm thinking a nice 3-3.5" exhaust system and a tune (chip). Plan to keep...

Any of you guys going to attend? I'm going for the long haul in #0408. Starting in detroit then ending in Dallas.

I need to get a carpet kit for the bed. I'm going to be making a trip in the Syclone and don't want to scratch it. Let me know what you guys have seen. Thanks in advance! Tony

Does anybody have an installed picture of the rpm cold air plate? I'm installing their stock battery location kit but can't find a picture of the plate installed. Thanks in advance!

Got this and the C5 Z06 brakes just about wrapped up. Sure is pretty stuff. I'll finally get to put my shiny new ZR1's on it too! BTW, I own a powdercoating company and can coat anything you guys need. Just send me a PM. If you notice in the pic you can barely see the inner fender liner...

Can you continue to use the stock bilstein or is there a specific Bilstein for a 2" drop? Thanks in advance!! Edit: I should add that I'm dropping the rear with the belltech drop leafs.

Pulling the hub for the C5 Z06 brake upgrade and both lower boots tore. Can you get just the boots for the factory lower ball joints? Truck only has 25K miles on it so the ball joints themselves are just fine. LMK if it's possible, and if there's a part number. Thanks in advance! Tony

Mine disappeared when I pulled the rear end for paint. These are the two clips (one per side) on the back of the rearend that hold the abs wire to the housing. LMK if you have any. I'll be glad to take 'em off your hands! Thanks, Tony strongtony97@yahoo.com

Looking at the renzfab front brake brackets for the Z06 calipers. What do I need to get for the back brakes? Got nice shiny new wheels and the idea of drums back there makes me sick. LOL What do I need to look for in order to get a nice set of disc brakes in the back?

Just got this truck to Texas. Has 25,500 miles on it and has a strong fuel vapor odor after driving. Is there anything known to typically fail on these related to the canister or vapor lines that I need to look for?

Straight syclone. Has had a bumper replacement due to a fender bender in the past. Has rust on the front fenders next to the cladding. 87k miles. Cracked dash but it all works apparently. What do y'all think?

Entertaining the idea of a V8 LS conversion. Don't wanna tear up my 25K mile truck so I figure starting with a clean roller is a better idea. Prefer something close to Texas. Let me know if you guys are aware of anything. My email: strongtony97@yahoo.com Thanks!!

I'm probably going to be purchasing a set of the black ZR1 replicas on ebay. Does anyone know if they require spacers on a syclone? I'll be putting the 11's on the rear and the 9 (or 9.5, whichever is available) in the front. Thanks in advance!

I'll get some pics of mine later. Just wanted to see what you guys drive other than syty's.

Any of you guys have a nice momo (or other brand) steering wheel in a syclone or typhoon? The wheel in my truck was changed at some point and I'm not a fan. Thought a nice momo or something might be an option. Thanks in advance! Tony

Noobie to the Syclone scene. Been wanting one since they were knew and I was 15 years old in '91. I just bought #0402 out of Oregon and will be bringing it back to Texas in the next couple of weeks. 25K miles, one owner since '92...hoping it's as nice as the owner describes. Any idea on what I...