Search results

I don't have a sy or ty anymore but im very interested in knowing and understanding how to read datamasters file. I have tons of old recordings from my ty and have read a lot from the help section of the program but when it comes down to the numbers I don't know what's right and wrong. where can...

Well here is the thing i just put this truck all back together from bending a push rod by myself. So im happy that i did it right and it runs right. :tup: In the process i upgraded the I/C to RPM's A/A and new lifters rods etc... I have the truck tuned for open down pipe and to run at 18-20...

Im looking for the Black color Heat Wrap to use on my A2A? Jegs mag did not have it. I know its out there?? :roll:

My truck screems a wistle from the throttle body. but if you just tweak the throttle a small amount it goes away. it only makes noise when the throttle body is closed. so could this be the throttle body gasket plenum gasket or intake manifold gasket??? neither??? or ????

Timming the distributor. when i use the timming light and line up the marks on the crank and idicator the truck is idle at like 2,000 rpm witch i dont understand???

How do you rotate Stock turbo housing? Thanks-

What are they where do the go i didnt unplug them so i dont know. Heres a pic this is one of the last things to conect before startup. [/URL][/IMG] The top one looks just like the black one to the coil but has orange and black lines so im lost?? the bottom one i have no idea??

In the process of replacing the push rods and lifters. Also... RPM Intercooler Electric fans A/C Delete [/URL][/IMG] [/URL][/IMG] Push Rod shown is the intake valve. In witch I drove the truck 20 Miles on. [/URL][/IMG]

I bent a pushrod and all my rockers are out of adjustment so time for new heads. Are there any good flowing heads out there that are direct bolt ons? also what has to be done to the intake manifold etc... if i was to go with vortec heads?

is the aldl cable the only cable i need with datamaster? also what do you do during the program to make changes after recording?

i have aldl cable and i was wonderin if i can mess around with the computer on my buick its a 91 with the 3.3L. I also would like to know how to connect to the ecm from datamaster to my truck. i guess instructions would work!

i know some people on here have these. Weight? Price? Size's? [/URL][/IMG]

The grey wire in the wiring harness in the pic below hard to see but its the grey one. Im tryin to tie up loose ends on this truck and this wire isnt comected to anything and have no clue if its important or what?? :squint: [/URL][/IMG] [/URL][/IMG] .

did a 0-100 and got into 3rd gear and realized that my rpms wernt getting higher and there was a problem slowed down and went to give it gas and in 3rd and 4th it sputter so bad it shook the truck bad only in 3rd and 4th got it to a buddys house and the o2 sensor that was used for tunnin only...

I lost from a roll to my buddy in his lightning he wins anytime except from a stop. that SS Trail Blazer beat me on the highway from a 70 punch and pulled away. WTF is goin on here i got rpm short block rpm tranny stock headers stock turbo stock chip tune with 50lb injectors atr with gutted cat...

Ok heres the thing i got RPM Tranny and a Locker rear end and a stock front end. I was driving down the highway and as i sped up over 60mph i felt and herd a vibration from what sounded like the front end. So i waited till i got off the highway cause i was goin to try and make it home but got...

Ran my buddys Cummins with 5' exhaust Smarty chip clutch and afe intake from a stop. And ran him 3 trucks all the way to 120.

Just got my typhoon tuned by Total Re-Cal down at Redline performance lil past festus missouri on highway 67. Did a great job and ill be goin back for sure after i get alcohol inject and a new 3" cat forward with electric cut out.

Whats the preferred oil of your choice? Company and Weight? Im running 10 w30 valvoline full syn. Let me here what everyone has to say about Pennzoil back when i worked at Jiffy Lube we took a 2day class just to get the job and wer told that they use a deturgent that creates a film and will...

Turbo is making a hissing sound while in or building boost now a whissle sound what could this be (stock turbo). Boost solenoid??? maybe?